Posts Tagged ‘UDI RD

29
May
17

UDI RC repair

Since my previous post https://pmetro.wordpress.com/2017/02/05/the-flying-computer what direction would be next? Since there are a overabundance of drones on the market,  many do not get that great of reviews, or over simplify the ease of flying and have a short flight time due to the size of the battery especially at the lower end price points. Some reviewers simply state that there is a lot of junk out there. If you are not experienced and want to join the ranks of drone operators, note recommendations and reviews of current high end drone operators with experience as to what drone they flew as a starter either as a racer or photographer, in other words what is cost effective for multiple  crashes.

Technology has progressed the drone into basically two types, at the higher end of the consumer market, racing or photography. As with other types of electronics smaller lighter and faster can be the general rule to racing drones and photography, (could also be branched out to heavy lifting) stability, reliability and stunning high definition cameras on remote control gimbals  have captured the market. The new announcements releases from leading drone manufacturers to drone operators is the same furor as  the latest smartphone presentation. Prices are reasonable as with every advance there is more technology for the price. This is a growth area with the application of different technology ever expanding.

Drones have given the radio controlled hobby market a kick in the pants. Certainly a few manufacturers have taken the lead and it reminds me of other breakout tech companies when a market first explodes, such as personal computers and cell phones. Some will be shaken out and others will consolidate. The amount of technology applications involved run from remote telemetry, autonomous control, GPS, vision and remote recognition as just a few before even getting into the array of sensors utilized to give the drones stable flight. Racers have not been left out , first person view, cameras and FPV vision goggles make these people look like Borg wanna be’s. Lipo battery technology give racers crazy amounts of power and brushless motor technology constantly boost the top speeds of these racing demons.

So instead of another complete kit, as of yet, after perusing the many hobby sites and quad copter forums, a new drone was out of the question, and trying to keep the cost low would limit me to an unreliable toy for learning flight. Now many of the online hobby shops  carry repair parts with some low cost consumer drone hobby models having practically all of the parts available to build one from the ground up, this is true with racing drones as they can be built in stages but would add up to a high cost , there would be an alternative to  gaining flight practice and  knowledge.     I decided a repair/modification of a drone would be the best route to become familiar with the types of technology being utilized. So off to the junkyard so to speak in search of a decent learner drone needing to be rescued. (Many first time drone buyers simply trying out the hobby crash and burn so to speak, so postings from Ebay on drones for parts etc. gave some promising results)

 

Note: If you want to repair drones look up replacement parts beforehand,  many models are supported either through the original manufacturer or third party sources, ALi Express, Banggood, Ebay, drone forums Etc. Much information can be obtained from hobby sites , you tube videos, online user manuals.

Lets get to it so we can fly….

 

From the drone bone yard, a UDI RC salvage from E-bay. Model 818A.

Basically bought from E-bay used, listed as one rotor not turning. After arrival and check,  one of the propellers is binding . After further checking the motor is the cause.

Ordered replacement motor and also a remote transmitter control  along with spare propellers as the control transmitter  was not included in the purchase this is another factor since many low priced drones have of their own proprietary remote transmitter. (more on this later)

Previously I had removed the canopy cover and propeller guard, a one piece snap off unit and unplugged the connections to the flight controller. Take pictures of the connections or draw up in a note pad a schematic before disassembly or research pin outs for the motor connections and LEDs of the flight controller board. (google etc.)

To disassemble the faulty propulsion unit , remove screw and disconnect strut from the main chassis. On the strut, carefully pry back the motor cover, slide it back and expose the motor. Remove necessary screws and draw enough wire from the strut to access the soldered connection to the motor. The other pair of wires is for the LED on that pod.

Compare the replacement component with the original, the gear is slightly different from the original. Note: The motors ( these are brushed motors) are highly magnetic keep them a distance from any magnetic sensitive material, keep work area clean from metal particles that would stick to the motor. (especially if you work on brushless out runner motors in the future) Also if you work with circuit boards, most all videos and instructions disregard the use of anti static precautions such as wrist grounding ground straps. Electronic Static Discharge can happen and disrupt sensitive electronics and cause a myriad of undetectable problems from total failure to loss or scrambling of data. If you have problems with circuit boards arriving DOA don’t discard that ESD may be the cause of failure. If you work with large amount of electronics or expensive components ESD precautions is cheap insurance. Once you open up the cover (like a cell phone) you have penetrated any shielding to sensitive devices and components.

Utilizing the insulation tubing from original, cut the conductors and solder in the replacement motor, of course following the original wired colored connections. Slip the insulation tubing over one of the soldered connections.

 

Carefully route the wires by gently pulling the through the strut from the opposite end, toward the flight controller. Double check the connection of the fragile wiring before securing motor cover.

secure cover of assembled unit. (bearing below propeller should be flush to top of strut, in this case the propeller shaft is a press fit to lower gear, align as necessary)

 

Make the PROPER  motor and LED and camera if equipped, connection the the main board of previously disconnected. Improper motor connection order will result in a flipping over or uncontrollable drone taking flight. (How do I know this?) Also if the flight controller board was removed from the chassis insure that the proper orientation of the board is followed, most aftermarket boards are marked with an arrow to indicate front (facing) of drone. Not this one. Accelerometers and gyroscopes have to know which way the are headed ! (in relation to the propulsion units). Troubleshooting skills here learned  for flight problems!

One note here: be extremely careful when pulling delicate connections from sockets, some manufacturers use a sealing or locktite type glue. Small connectors such as 2 conductors plugs, grasp the connector , not the wires to disengage. Some sockets  are surface mount soldered and could be pulled directly from the circuit board necessitating a re soldering of socket to the main board.  If plug does not disconnect readily, be aware and proceed cautiously.

At this point (with propellers removed) you could attach battery, pair up the transmitter  and test the motors.

 REMOVE PROPELLERS BEFORE TESTING

 REMOVE PROPELLERS BEFORE TESTING

Rotors should be removed when you power up drone after modification, some unexpected reactions at times will cause the flight controller to start all propellers when battery is connected, due to an improper wiring or damaged flight controller. Assume that motors may start at any time. Again remove propellers.

Checking connection and LEDS, so far the drone is looking good, battery connection resulted in proper lighting and (not shown) blinking led on flight controller)

Secure cowling by snapping on cover/propeller guard. Mount LED headlight (white single LED). Power down and follow manufacturers direction for pairing transmitter, calibration and flight.

Most all drones have a user manual that can be found online. Some might have different conventions on flight controller and transmitter synchronizing  (pairing).

Progressing up the ladder on Radio Control it’s advantageous to get a transmitter that will support multiple Quadcopters, but this comes at a cost and matching transmitter and receivers  to flight controllers is a later lesson. Most of the low cost hobby drones require each their own radio control transmitter  system. When buying drones less a transmitter (control) research if you can buy a reasonable required replacement transmitter as they more than not will  not work with any other type for drone. Or you could swap out the flight controller with one that you already have a properly matched receiver (and/or flight controller) and transmitter using the frame and motors of the drone you are repairing.

**********************************************************

Will it fly ?  Yes ,I was lucky as the motor was the only problem with the drone.

The firmware of the flight controller was undamaged, there is no USB or software available to re-flash the flight controller as in the case of the MultiWii.

The UDI RC with the propeller shroud can take many crashes and collisions without damage. It’s a good learner drone. I have yet to test the camera out.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<UPDATE>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

The UDI drone has flown many times and is a learning challenge to pilot just around the house. The propellers are protected by the cover/shroud so they only get slightly chipped in my flights. It’s not ultra stable per say, but after some trimming of the controller pitch, roll, and yaw, easy to get to flight with the limited room indoors available to fly. Probably replacement of all 4 motors and prop balancing would improve stability. A good flyer none the less and time to move on to other repairs and construction. Several high capacity 1s batteries were purchased for increased flight time.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

So could I have bought a complete  used drone instead of a damaged one? Probably so, but missing a education experience and satisfaction of repair, disassembly, motor wiring and how the drone is constructed. Modifiable? Snap off the cover and ditch the camera for weight savings, disconnect the LEDS for power savings, go with slightly larger or smaller props  and  beef up the battery with a higher capacity replacement. Add an FPV camera ? Maybe a trick out paint job or more LEDS?

Drone :  $9.99 Ebay

Controller : $16.65 Ali Express

Motor: $5.31 Ali Express

optional replacement propellers: $2.88 Ali Express

shipping for the drone was about $10.00

shipping for the propellers $2.04

other items shipped free

NEXT : Can a Propel Spyder XL (chromed) be returned to flight status ?




Archives

October 2017
S M T W T F S
« Sep    
1234567
891011121314
15161718192021
22232425262728
293031  

Recent Posts


Talking Hydroponics

Growing & Much More

Power Plant Men

True Power Plant Stories

Bottles & Cans & Just Clap Your Hands

Rhode Island’s Better Beer Blog • by Lou Papineau • @BottlesCansRI • bottlescansclaphands@yahoo.com

GoanImports.com

Learn Goan and Indian Recipes

Healthy Cravings

scrumptiously good

adorable life

eat,craft,travel,love...in short live your life and njoy

cooking from the heart

inspired by june & norma

Little Observationist

A journal of observations & inspirations by Stephanie Sadler

RecipeReminiscing

Food the old fashioned way

Beer Hobo

Words and photos from the road

Alcoholidays with Mama Bear

"I feel sorry for people who don't drink. When they wake up in the morning, that's as good as they are going to feel all day." -Dean Martin

spf 99

my two ounces

Bard's Home Brew Brewery

A Homebrew Journey

Amintiri din Bucătărie

Memories from the Kitchen

Beyond Mere Sustenance

Food as a lifestyle...

TwistedSifter

The Best of the visual Web, sifted, sorted and summarized

rise of the sourdough preacher

Of homemade bread, food and other recipes / Una storia di pane fatto in casa, cibo ed altre ricette

Rugutis

The spirit of fermentation

JEFFREYTHARP.COM

A voice of sanity in a world gone mad...

Later On

A blog written for those whose interests more or less match mine.

My Food and Me

... just about food and more food!!!

my sister's pantry

Eat food... real food

Rantings of an Amateur Chef

Food...cooking...eating....tools - What works, and what doesn't!

Two Barn Farm

Sustainable Farming, Permaculture, Gardening and Homesteading in Ohio

Little London Observationist

An expat blog about "the little things" in London

Mom de Cuisine

Culinary Musings of an Expat Mom

El fogoncito

Comida tradicional Dominicana y algo más...

gettin' fresh!

turning dirt into dinner

Let's Spice Things Up

Recipe Reviews, Tips & Ideas from my table to yours!

talinorfali

Don't ever change yourself to impress someone, cause they should be impressed that you don't change to please others -- When you are going through something hard and wonder where God is, always remember that the teacher is always quiet during a test --- Unknown

ediblesubstance

A foodie's thoughts

Food in Jars

a little mech, tech, and food

Las Vegas Food Adventures

From a Las Vegas native's point of view

cupcakejunky

Fashion, Food, Interior Design and Architecture

Rachel & Maya

Dishing about all things food related.

Advoken's Blog

Just another WordPress.com weblog

Croque-Camille

Food Adventures in Paris

Veggicurious

Creative and exciting vegetarian food featuring bold flavors and world-wide cuisines. Plant-based cooking can be anything BUT boring.

Cooking in Tongues

Savoring the world through food, trails and photos.

con tomates

Juicy living in the Iberian Peninsula and beyond

WordPress.com

WordPress.com is the best place for your personal blog or business site.

Slow Food RI

Slow Food Rhode Island is the Rhode Island chapter of Slow Food USA.

The WordPress.com Blog

The latest news on WordPress.com and the WordPress community.

%d bloggers like this: